Cabinet Hardware Counter, American Fork
Clarksclankers LLC is a small cabinet hardware supplier working out of its counter at 125 E Main St, American Fork - 84003-2407, United States (US). We keep hinges, pulls, catches and restoration stock on the shelf so a fitter can walk in with a drawer in mind and walk out with the exact part that closes it cleanly. Our whole trade is the moment a door settles into the frame and the hardware answers with one crisp, true clank.
Clarksclankers LLC exists because cabinet hardware is where a kitchen, a workshop bench or a shop display either feels finished or feels loose forever. We treat every hinge, pull, latch and catch as a measured decision, not a grab from a bin.
The work at our American Fork counter starts with measurement. A cabinet door that rubs at the top corner tells us more about the carcass than about the hinge, and a drawer that drags on one rail usually needs a pull matched to its real weight rather than a heavier screw. We read those signals, then reach for stock that fits the opening as it actually is. That habit is why tradespeople from across the valley bring a single leaf, a broken catch or a bag of orphaned knobs to the counter and ask what we think. We think out loud, we test the swing, and we let the hardware tell us when it is right.
Our stock leans toward honest, serviceable parts: solid brass and steel hinges with real knuckles, cup pulls with a comfortable throw, magnetic and roller catches that hold their tolerance, and finishing supplies for the older fronts that deserve another decade. Because we are a supply counter first, we can sell a single unit to a weekend repair or a full pallet to a shop build. The same person who answers the phone will often be the person who tells you which side of the leaf to mortise and how deep to set the plate. That directness keeps the trade simple and keeps the clank honest.
We also keep a working relationship with the six services that fill most of our week: hinge fitting and alignment, drawer pull matching, latch and catch setup, hardware restoration, bulk trade supply and fit clinic appointments. They are not separate businesses. They are the same counter read six ways, and together they cover the full life of a cabinet front from first install to a patient restoration.
Six leaves pinned to the board, each one a service we run every week. The width of the leaf tells you how much counter time it usually asks for.
We set and align cabinet hinges so doors close flush, sit square in the frame and hold their line through a full season of use. The work covers overlay, inset and partial overlay leaves, and it always starts with a swing test before a single screw is turned. Read more →
We match pulls to drawer width, weight and throw so a run of fronts reads as one set and opens with one comfortable movement. Center to center spacing, projection and finish are all part of the match, and we keep sample pulls on the counter to compare in daylight. Read more →
We install and tune magnetic catches, roller catches, touch latches and push to open mechanisms so a door holds closed without a fight. The trick is almost always in the strike plate position and in the tension, both of which we set by feel and then by measure. Read more →
We bring tired brass, steel and bronze hardware back into service rather than sending it to a landfill. Cleaning, re-tensioning, replacing worn springs and refreshing finishes all happen here, and we are honest when a part is past saving and a replacement is the better spend. Read more →
We supply builders, shop fitters and cabinet makers with hardware by the box and by the pallet, priced for trade and counted accurately. Orders can be pulled against a cut list, staged for pickup, and packed so that the smallest screw does not go missing between the counter and the job site. Read more →
Bring a stubborn door, a drawer front or a box of unknown parts to a booked fit clinic and we work through it with you at the bench. These sessions suit homeowners, renovators and new fitters who want to learn the feel of a correct fit rather than guess at it. Read more →
Clarksclankers LLC opens its autumn fitting weeks at the American Fork counter, and the board is already taking bookings for hinge alignment and catch setup through the season.
Four steps carry a job from the first question to the last clank, whether you are a homeowner with one drawer or a shop with forty fronts.
You bring the opening, the leaf or the front, and we measure it together. Photos and a short phone call work when a visit to 125 E Main St is not possible.
We pull candidate hinges, pulls or catches from the shelf and compare them against the real opening, not against a brochure number.
We fit, set and re-tune until the swing, hold and release all feel right, adjusting the plate, the tension or the throw as the part asks.
You leave with the right count for the job and a note of the parts used, so the next match is a quick call rather than a fresh search.
A single cabinet hinge sold across the counter is as welcome as a pallet order for a shop fit. We keep solid brass and steel leaves, cup pulls and bar pulls in several finishes, magnetic and roller catches, shelf pins, screws in the sizes that actually get lost, and the small alignment shims that save a crooked door. Because we stock deep rather than wide, a caller rarely hears that the part is out of reach.
For trade buyers our bulk trade supply desk pulls against a cut list and stages orders for pickup, so a fitting crew can collect a full job in one trip. Counts are checked twice, and every box is packed so that hardware arrives sorted rather than in one heavy bag of loose parts.
The other half of the counter is advice. Fitting a hinge is a short lesson in patience: set the top screw lightly, watch the gap, then bring the leaf in until the door meets its frame with even pressure. We teach that sequence at fit clinic appointments so a first timer leaves able to repeat it. Restoration work gets the same care, and we explain the cleaning and tension steps for hardware restoration so the fix holds.
Latch and catch setup is where our guidance saves the most frustration, because a door that refuses to stay closed is almost never a bad catch. It is a strike plate a millimeter off, and we will show you where the pencil mark should land. That kind of teaching is free at the counter and it is the reason people come back with the next drawer instead of the next catalogue.
The same counter serves very different rooms, and the hardware has to respect each one.
A kitchen in American Fork wants pulls that sweep cleanly, hinges that soften a heavy door, and catches that hold a cabinet closed through daily use. A workshop bench wants drawer fronts that open with a gloved hand, which usually means a wider pull and a catch with real tension. A restoration room wants the opposite of new: period correct leaves, cup pulls with a worn finish and springs that can be retensioned rather than replaced with something modern. We keep examples of each on the wall so the difference is visible before a decision is made.
We also work with shop fitters who need a display cabinet to read as a single object. That means every pull matched for projection and finish, every hinge set at the same reveal, and every catch tuned to the same release pressure. When the run is finished we walk it front to back and open each door, listening for the one clank that tells us the set is even. If one door sounds different, we adjust it on the spot rather than leaving it for someone else to notice.
Restoring older cabinetry is the most patient branch of the work. Original brass often carries decades of grime that hides a good surface, and a steel leaf can be saved with a clean, a re-tension and a touch of finish. We would rather spend an afternoon on a set of fittings that will outlast a modern kit than sell a replacement that matches nothing around it. That preference shows in the shelf we keep and in the questions we ask before recommending anything.
Whatever the room, the promise is the same. Measure honestly, match carefully, fit so the hardware disappears into the cabinet and only the action remains. The result is a front that feels considered each time it moves, which is the whole point of a hardware counter that cares about the fit. To arrange a visit or a clinic session, use the contact page, call +15099068321, or stop by the counter at 125 E Main St, American Fork - 84003-2407, United States (US).