Six Fitting Services, One Counter
Cabinet hardware supply and
fitting guidance, set leaf by leaf,
so every front gives back its Clank.
Clarksclankers LLC runs six services from its counter at 125 E Main St, American Fork - 84003-2407, United States (US). Each one is a distinct trade with its own tools and its own patience, and each one ends the same way: a cabinet front that moves as if it were always meant to. Below is what we do, how a job runs, and how to start.
Hinge Fitting and Alignment
Hinge fitting is the service that most often decides whether a cabinet feels expensive or improvised. We work with overlay, partial overlay and inset leaves, and we start every job with a swing test before touching a screw. The goal is a door that sits flush in its frame, carries an even reveal on all four sides and returns to the same position every time it is let go. We set the top screw lightly, watch how the leaf responds, then bring the door in until the gap closes smoothly rather than being forced shut.
Alignment is where the small adjustments live. A door that drops at the far corner needs its lower leaf brought forward a fraction, and a door that rubs at the top usually needs the upper plate eased rather than the frame reshaped. We carry steel and solid brass hinges with real knuckles so the swing stays true under a heavy door, and we check each pair for a matching tolerance before fitting. When a run of doors is involved, we record the reveal we used so every front in the room reads as one set.
We also handle the cases that frustrate homeowners most: the door that never quite closed after a repaint, the cabinet that was hung out of level, and the leaf that was mortised a little too deep. In each case we work with the opening as it is, choosing a hinge plate or a shim that absorbs the error rather than asking the owner to rebuild the carcass. The result is a fit that looks deliberate and sounds correct, which is exactly what a hinge should deliver.
Drawer Pull Matching
Drawer pull matching is a study in proportion. A pull that is too small for a wide front looks lost, and a pull that is too heavy for a narrow drawer makes the front feel clumsy in the hand. We match pulls to drawer width, expected load and the throw a user wants, so the whole run opens with the same comfortable gesture. Center to center spacing, projection and finish all enter the decision, and we keep sample pulls on the counter so they can be compared in daylight rather than under a shop light.
Finish matching is quieter but just as important. A brushed brass cup pull beside a polished one will read as someone running out of stock, even if both are technically the same size. We compare tone and sheen across a set before recommending anything, and we are happy to source a small quantity of an unusual finish when a display cabinet needs to stand out. For kitchens we tend toward cup pulls and bar pulls with a comfortable underside, while workshop fronts often suit a wider pull that a gloved hand can catch.
When a drawer front is being replaced or a label is being repositioned, we also help with hole placement so a new pull covers the old fixing points or lands cleanly beside them. That small planning step saves a front from being drilled twice and keeps the spacing even across a full bank of drawers. Matching is not about picking a favourite shape; it is about reading the drawer and giving it the pull it was waiting for.
Latch and Catch Setup
A door that will not stay closed is almost never a bad catch. It is a strike plate a millimetre off, or a tension screw set too loose, and finding that is the whole craft of latch and catch setup. We install and tune magnetic catches, roller catches, touch latches and push to open mechanisms, and we set each by feel first and by measure second. The target is a door that holds firmly without a fight and releases with a light, even pressure.
Magnetic catches suit doors that need to sit quietly and stay put, especially where a handle is fitted and the user expects a soft close. Roller catches suit heavier doors and give a firm, audible hold that reassures the hand. Touch latches and push to open fittings suit handle free fronts in modern kitchens, and they ask for careful setting because a few millimetres decide whether the door pops open or stays sealed. We carry the strike plates and spacers that make these adjustments possible without redrilling.
We also tune catches after a hinge adjustment, because changing a door swing can change where the catch meets its strike. Clients at the counter are often surprised that a five minute catch adjustment solves a problem they had blamed on the cabinet. That is the value of treating the door as a system: the hinge, the catch and the pull all have to agree, and when they do, the cabinet closes with one clean clank.
Hardware Restoration
Restoration is the patient branch of our trade. Original brass and steel hardware often carries decades of grime that hides a perfectly serviceable surface, and we would rather bring that surface back than sell a modern replacement that matches nothing around it. Cleaning, re-tensioning, replacing worn springs and refreshing finishes all happen at our bench, and we are honest when a part is past saving. A brazed hinge leaf with a cracked knuckle is usually a replacement job, and saying so saves the customer money and time.
The work begins with a clean and an inspection. We remove what a gentle solvent releases without stripping the good surface underneath, then examine the knuckle for wear and the spring for a lost temper. Where a spring can be retensioned we do it, and where it cannot we match a replacement that respects the original feel. For cup pulls and knobs we refresh the finish so a restored set reads as one family, not as four parts that survived the years differently.
Restoration suits heritage cabinetry, older shop furniture and any piece where the fittings are part of the story. Bringing a set back means the drawer tells its history through the wear that remains while the action feels new. We enjoy this service because it rewards attention, and because a restored catch that snaps closed after a careful afternoon is one of the most satisfying sounds at the counter.
Bulk Trade Supply
Bulk trade supply serves the builders, shop fitters and cabinet makers who need hardware by the box and by the pallet. We price for trade, count accurately and pack so that a job arrives sorted rather than as one heavy bag of loose pieces. An order can be pulled against a cut list, which means the counter reads your door and drawer schedule and draws the exact quantities, rather than asking you to convert a schedule into a purchase order by hand.
Staging is part of the service. When a fitting crew is working across several rooms, we separate the hardware by space and label each bundle, so the right hinges and pulls land in the right room on the right day. We keep common sizes deep in stock so a shortfall does not stall a job, and we can hold a small reserve against a call back. For a refurbishment we can also set aside the same finish and batch across a whole order so the pulls match from the first cabinet to the last.
Because we are a counter first, a trade buyer can talk to the person who packed the order. That matters when a site has an unusual reveal or a door that needs a special leaf, because the conversation is short and the answer is usually on the shelf. Bulk supply is not a warehouse exercise for us; it is the same careful matching we do for a single drawer, repeated across a job and priced for trade.
Fit Clinic Appointments
Fit clinics are booked sessions at the bench where we work through a stubborn door, a drawer front or a box of unknown parts with you. They suit homeowners, renovators and new fitters who want to learn the feel of a correct fit rather than guess at it. Bring the actual hardware if you can, and we will measure, match and set it together while explaining each step. Most clients leave able to repeat the sequence on the next cabinet without help.
A clinic usually runs through the full chain: reading the opening, choosing a leaf, setting the swing, tuning the catch and matching the pull. We keep the pace friendly and answer questions as they come, because a fit is easier to learn with your hands on the part than from a diagram. If a piece needs restoration, we can move that work to the bench and show the cleaning and tension steps as well.
Booking is simple. Use the contact page, call +15099068321, or stop by the counter at 125 E Main St, American Fork - 84003-2407, United States (US). Bring a rough idea of what the cabinet is doing wrong and we will take it from there. A clinic is a good first visit for anyone who wants their cabinets to feel as considered as the rest of the room.
How A Job Runs
Four steps carry any service from the first enquiry to the last clank.
Measure And Describe
Bring the opening, the leaf or the front to the counter, or send photos and a short description if a visit is not possible.
Match The Stock
We compare candidate hinges, pulls or catches against the real opening, not against a catalogue number.
Fit And Tune
We fit, set and re-tune until the swing, hold and release all feel right, adjusting as the part asks.
Supply And Follow Up
You leave with the right count and a note of the parts used, so the next match is a quick call.
Clarksclankers LLC opens its autumn fitting weeks at the American Fork counter, with clinic sessions bookable for hinge alignment, catch setup and pull matching.